Enable Administrator account Windows 7 Domain

First thing you will do is boot your computer in Windows 7 and Choose Repair your Computer as shown below

Figure1

Then it look for available operating system and let you choose for a compatible OS then click next

Figure2

In System recovery option choose Command Prompt

Figure3

In your Command Prompt type regedit and it will show the image below. 

Figure4

Click HKEY_USERS then go to file tab then Load Hive

Figure5

In your Load Hide window look in the drive that is shown in Figure2, in my case it is in drive D:\Windows\System32\Config then select SAM, click open

Figure6

Then type SAM_TEMP and click ok

Figure7

In your registry editor go to HKEY_USERS\SAM_TEMP\SAM\Domains\Acount\Users\000001F4 then double click F

Figure8

Change '11' to '10' located in row 0038 as shown below then click OK

Before

After

Click SAM_TEMP then in your file tab choose Unload Hive and click yes

Close Registry Editor and exit the command prompt. In your System Recovery Option Window click Restart. When the computer is connected to domain just type .\Administrator and hit enter.


Reference:
Best Practive: How to enable a disabled Local Administrator account offline in Windows 7 (even when using BitLocker)

Setting up CloneZilla Server in Ubuntu 12.04

I'm usign Ubuntu 12.04 64 bit. After DRBL installation you need to setup the server. I am using two network cards, 1 for my internet connection the other one is for Clonezilla Server. In the upper right side of your Ubuntu desktop click the network indicator and then choose edit connection

Then choose Wired connection 2 because the Wired connection 1 is for my internet access, then click edit

after you click edit choose IPV4 Settings Method should be manual then click add and then save.
Address: 192.168.1.254
Netmask: 255.255.255.0
Gateway: 192.168..254

Next go to you terminal (Ctrl+Alt+T) type sudo drblsrv -i

After the drblsrv installation type sudo drblpush -i

I choose the default option. If the following wont work try drbl4imp
Note: type: nano /etc/rc.local and at the end of the file, add drbl-all-service start, save and exit

Reference: Clonezilla SE - Server and Network Configuration, Clonezilla Installation

BOOTMGR is missing

To fix BOOTMGR is missing of a Windows 7 operating system you must have the Windows 7 installer. This error usually happen when a computer is not properly shutdown or force shutdown results to corrupted file system or it can be an operating system upgrade. First thing to do is boot (F8, F12, esc and etc) it to Windows 7 installer. When you see the figure below just click next

Figure 1

then choose repair

Figure 2

After it will search for a system recovery option as shown below

Figure 3

Then choose the Window 7 operating system and click next. Sometimes it will ask you to restart before Figure 4 is shown, if that happens just restart and then do the same step until you reach Figure 4.

Figure 4

You can either choose Startup Repair or Command Prompt

Figure 5

In Startup Repair it automatically check errors and repair it as shown below

Figure 6

until it will show you that it is fix successfully  then click finish.

Figure 7

In command prompt you just need to type bootrec /fixboot and press enter. Restart and you are done.

Figure 8

Reference : 

Fixing "BOOTMGR is missing" Error While Trying to Boot Windows 7 or Vista, 

What does the “BOOTMGR is missing” error mean?

Setting up Django in Eclipse

I am using Windows 8, Django 1.5.2, Eclipse IDE for Java EE Developers 64 bit, MySQL Workbench 5.2.47 CE, Python 2.7.5 64 bit since I can't get Python 3.3 to work because the requirement of MySQL-python-1.2.3.win-amd64-py2.7 is Python 2.7. ez_setup.py just copy and paste the content and save it as ez_setup.py same with get-pip.py and place it to where your Python27 folder is located, as for me it is in C:\Python27. Add: C:\Python27;c:\python27\scripts;c:\python27\bin to PATH. 

In your command prompt type cd C:\Python27 then python ez_setup.py. When it's done type python get-pip.py. Next is to install django just type in you command prompt pip install django

After the following software mentioned above are installed, in your Eclipse go to help and click eclipse market place as shown in Figure 1

Figure 1

  
Then in the search tab type Django and click install, in my case it is already installed, basically you will just have to click and agree to everything until you are ask to click finish.

Figure 2

Next is go to preference

Figure 3

In your preference window click PyDev and then choose Interpreter - Python then click Auto Config and basically just agree to what is ask and click that is related to your python 2.7. 

Figure 4

Then add Django folder to PYTHONPATH as shown in Figure 5, click ok and apply settings

Figure 5

In creating a new project just go to file, new then others, as shown below.

Figure 6

Then choose PyDev Django Project

Figure 7

Type in the project name. I choose python 1 because that is the file name of my interpreter where python27 is created, then click next

Figure 8

In Django Settings before you type in the info of your mysql details you have to create firs a database in MySQL Workbench, so basically in Figure 9 are the info of my mysql.

Figure 9

In MySQL Workbench configuration just click Create New EER Model

Figure 10

and double click mydb and type below the mysql database filename that you desire, in my case its coop as shown in Figure 9, then save your database.

Figure 11

After my project is created go to run configuration as shown below 

Figure 12

Then follow the image below

Figure 13

Just type in the name Django 1.5.1 and then browse the Django file in your computer as for me it is located in C:\Django-1.5.1 

Figure 14

click OK until you find the image below and you are ready for coding your Django

Resources: 
Django: Installing Eclipse and PyDev for django, Using Django 1.4 with Eclipse, Install Django in Eclipse with PyDev on Windows 8

Saving and restoring image using Clonezilla Server in Ubuntu 12.04

I'm using Ubuntu 12.04 64 bit

After installing clonezilla server, in your terminal (Ctrl + Al t+ T)  type:
sudo su
type the password
dcs

it will show you Figure 1, select the "All select all the clients" and then follow the highlighted text in the figure

Figure  1

Figure 2

Figure  3

This set-up will let your client choose individually whether to save or restore the image in your server

Figure  4

To be safe I choose the default configuration

Figure  5

Figure 6 will do nothing after restoring or saving the image, unless you type poweroff (that is one word)

Figure 6

Figure 7 shows that you are done for individual clients settimgs

Figure 7

If you want to set-up more clients to save or restore at once, choose save disk or restore-disk 

In this example I will choose restore disk.

Figure 8

Figure 9

Figure 10 shows the save image that you want to restore to your clients.

Figure10

Figure 11

Figure 12 will ask you how many clients to clone

Figure 12

In this Figure 13 I put 21 clients

Figure 13

Figure 14

You are done with restoring images.

In saving a file same step with restoring images, the only difference is it will ask you the file name as shown in Figure 15

Figure 15

Note: In setting up your client make sure that the OnBoard LAN is enable you can find this in your bios setup






Reference:
CloneZilla Saving and Installing image